文献类型：期刊文献

中文题名：乙基纤维素包覆成型活性炭的制备及其性能研究

英文题名：Preparation and Properties of Formed Activated Carbon Coated by Ethyl Cellulose

作者：许伟[1,2,3,4] 刘军利[1,2,3,4] 缪存标[5] 孙康[1,2,3,4] 宋曜光[1,2,3,4]

第一作者：许伟

机构：[1]中国林业科学研究院林产化学工业研究所;[2]生物质化学利用国家工程实验室;[3]国家林业局林产化学工程重点开放性实验室;[4]江苏省生物质能源与材料重点实验室;[5]福建元力活性炭股份有限公司

年份：2017

卷号：37

期号：2

起止页码：49-56

中文期刊名：林产化学与工业

外文期刊名：Chemistry and Industry of Forest Products

收录：CSTPCD;;Scopus;北大核心:【北大核心2014】；CSCD:【CSCD2017_2018】；

基金：“十二五”国家科技支撑计划资助(2015BAD14B06)

语种：中文

中文关键词：成型活性炭;表面包覆;强度;水接触角

外文关键词：formed activated carbon ; surface coating ; strength ; water contact angle

分类号：TQ35;TQ424.1

摘要：以乙基纤维素(EC)为包覆材料,无水乙醇为溶剂,在50℃溶解制成包膜液。将制备好的包膜液均匀地喷涂在成型活性炭的表面,经热处理后,制备得到包覆EC的活性炭产品。考察了包膜液的质量分数、喷涂体积及热处理温度对包覆活性炭强度和吸附性能的影响。结果发现:膜液质量分数4.23%、30 g活性炭喷涂20 m L膜液、热处理温度140℃条件下,制备的包覆活性炭产品强度达93.66%,相比原料活性炭提高7.35个百分点,丁烷工作容量为86.0 g/L,相比原料活性炭下降9.6 g/L,在活性炭表面形成了一层3~4μm的薄膜。EC包覆没有改变活性炭内部的孔结构特征,但会影响活性炭表面的润湿性,经EC包覆后活性炭水接触角(θ)为89.76°(原料活性炭的θ为15.41°),疏水性能显著提高;包覆后的活性炭产品表面光滑平整,无浮尘,形状保持良好。
The coated liquid was prepared with ethyl cellulose as coating material and ethanol as the solvent by dissolving at 50 ℃. In order to prepare activated carbon products coated by EC, the coated liquid was uniformly sprayed on the surface of formed activated carbon before heat treatment. The influences of the mass fraction of coated liquid, spray volume and heat treatment temperature on the strength and adsorption properties of coated activated carbon were studied. It was found that under the mass fraction of coated liquid was 4. 23% ,the weight of activated carbon was 30 g,the spray volume was 20 mL,and the heat treatment temperature was 140 ℃, the strength of the coated activated carbon reached 93.66% and increased 7.35 percentage points compared with that of raw activated carbon and the butane working capacity reached 86. 0 g/L and decreased by 9. 6 g/L, a thin film with thickness 3-4 μm was formed on the surface of the activated carbon. EC coating did not change the pore structure of activated carbon, but it would affect the wet ability of activated carbon surface, the water contact angle of coated activated carbon was 89. 76°, which of the raw activated carbon was 15.41 °, and it meant the hydrophobic performance was significantly improved. The surface of the activated carbon products prepared by this method was smooth, no dust, and the shape kept well.